Dryer Safety

Dryer Vent Repair or Cleaning: Which Do I Need?

Most dryer vent problems fall into one of three jobs: cleaning, replacing the vent or installing a new vent path. Here is how to tell which one you have, what Minnesota's code requires and who to call.

Dryer pulled from a basement wall, its foil accordion duct kinked and sagging, with a straight metal duct and a metal elbow on the floor

A dryer vent clogged with lint needs cleaning. A vent that is crushed, torn, disconnected or made of plastic needs replacing. A vent that must be rerouted, or a new path through a wall or roof, needs a contractor. MedCity Duct Cleaning in Rochester, MN cleans dryer vents and can replace the vent; we don't repair vents.

If you searched for "dryer vent repair near me," here's what to expect in this guide:

  • When cleaning is enough
  • When the vent needs replacing
  • What Minnesota's code requires
  • Who installs or reroutes a dryer vent
  • What you can check yourself

When Does a Dryer Vent Just Need Cleaning?

When the vent is intact and connected but lint has built up inside. The U.S. Fire Administration found that failure to clean (34 percent) was the leading factor in the ignition of residential clothes dryer fires in 2008 to 2010, the most recent data in its report. It says heavy clothes that take a long time to dry, or clothes that feel hotter than usual at the end of the cycle, point to a clogged vent. See why a dryer takes two cycles and why a dryer smells like burning.

When Does a Dryer Vent Need to Be Replaced?

When the vent itself is the problem. Cleaning won't fix these:

  • Crushed or kinked sections. The Fire Administration says to check that the venting behind the dryer "is not damaged, crushed, or restricted."
  • Plastic or foil accordion hose. The U.S. Consumer Product Safety Commission says it "can more easily trap lint and is more susceptible to kinks or crushing." The Fire Administration recommends rigid, non-ribbed metal duct instead.
  • Torn or disconnected sections, or a vent that doesn't meet the code below.

We don't repair dryer vents; we believe a damaged vent is better replaced.

What Does Minnesota's Code Require for a Dryer Duct?

Minnesota Rules, part 1346.0050, adopts the 2018 International Mechanical Code as part of the Minnesota Mechanical Code. Section 504 of the code as adopted in Minnesota covers dryer exhaust. The key points, as we read them in November 2026:

  • Material: metal at least 0.016 inch thick, with "a smooth interior finish."
  • Size: "4 inches (102 mm) nominal in diameter."
  • Transition duct (the connector behind the dryer): one length listed to UL 2158A, no longer than 8 feet, and it "shall not be concealed within construction."
  • Joints: ducts "shall not be joined with screws or similar fasteners that protrude more than 1/8 inch (3.2 mm) into the inside of the duct."
  • Outside end: it "shall be equipped with a backdraft damper. Screens shall not be installed at the duct termination."
  • Length: 35 feet, less for elbows, unless the dryer's instructions set the limit. See how long a dryer vent can be.

For a question about a specific home, ask your local building official.

Who Installs or Reroutes a Dryer Vent?

A contractor who does ventilation work, or the installer delivering your dryer. For a new path through a wall or roof, call a contractor. After a January 2025 Rochester dryer fire, the Rochester Fire Department told KTTC that it is extremely important that appliances are vented properly.

Want to see what's in your ducts?

Request a free estimate — no obligation.

What Can I Check Myself?

  1. Clean the lint screen before or after every load, as the CPSC advises.
  2. Look behind the dryer. Is the hose attached at both ends and not crushed?
  3. Run the dryer and check outside. The CPSC says that if exhaust air isn't escaping, "the vent or the exhaust duct may be blocked."

Frost or water at the hood in winter? See frost or water in a dryer vent.

What Does MedCity Do on a Dryer Vent Job?

On a dryer vent cleaning, we trace the run from the dryer to where it exits your home, checking its length, turns, vent material and exterior vent cap. We clean the full run with our Rotobrush dryer vent system and verify the airflow outside.

If the vent is crushed, damaged or the wrong material, our technician carries what is needed to replace it. We replace it on request, or when it's needed to do the cleaning and bring the vent up to code. We quote online or over the phone based on your home's details, and a walk-through the day of your appointment confirms the quote before we begin.

Why Does This Matter in Rochester?

The Fire Administration found residential dryer fires were more common in fall and winter, peaking in January at 11 percent. After Rochester's Jan. 6, 2025, dryer fire, Assistant Fire Marshal Jason Fife said cleaning the lint out once a year "reduces your fire risk." We recommend a dryer vent cleaning at least once a year.

Frequently Asked Questions

Do I need my dryer vent repaired, replaced or just cleaned?

Cleaned, if the vent is intact but full of lint. Replaced, if it is crushed, torn, disconnected or plastic. If it needs a new route through a wall or roof, call a contractor.

Who installs or reroutes a dryer vent in Rochester, MN?

For a new vent path through a wall or roof, call a contractor who does ventilation work, or ask the installer delivering a new dryer. MedCity Duct Cleaning cleans dryer vents and can replace the vent.

Can a crushed or foil dryer vent be replaced during a cleaning?

Yes. We don't repair dryer vents, but our technician carries what is needed to replace the vent. We do it on request, or when a replacement is needed to finish the cleaning and bring the vent up to code.

What does Minnesota's code require for a dryer duct?

Metal at least 0.016 inch thick with a smooth interior, 4 inches in diameter, ending outside with a backdraft damper and no screen. The connector from the dryer must be one listed transition duct no longer than 8 feet, not concealed within construction.

When does a vent need to be replaced instead of cleaned?

When cleaning can't restore airflow, as with a crushed or kinked section. The U.S. Fire Administration recommends replacing coiled-wire foil or plastic venting with rigid, non-ribbed metal duct.

Who handles a broken vent flap or hood outside?

We inspect the vent cap on every dryer vent cleaning and tell you if we find an issue. The code requires a backdraft damper at the outside end. If the fix means work on the siding, wall or roof, call a contractor.

My new dryer won't reach the old vent. What should I do?

Ask the dryer installer or a contractor. The code allows one transition duct up to 8 feet, so don't join hoses to make up the distance. Extending or moving the fixed duct is installation work for a contractor.

Can I join dryer duct sections with screws?

Not with screws that stick out into the duct. The code says ducts shall not be joined with screws or similar fasteners that protrude more than 1/8 inch into the inside of the duct, because lint catches on them.

How long can a dryer vent be under Minnesota's code?

Up to 35 feet from the dryer connection to the outside, reduced for each elbow, unless the dryer maker's installation instructions set the limit.

How often should a dryer vent be cleaned?

At least once a year. Rochester Fire Department Assistant Fire Marshal Jason Fife told KTTC in January 2025 that cleaning the lint out once a year helps the dryer work better and reduces your fire risk.

Not sure whether your vent needs cleaning or replacing? Learn about dryer vent cleaning, request a quote online or call us at (507) 289-4039.

Sources

  1. Minnesota Mechanical Code 2020, Chapter 5, Section 504 Clothes Dryer Exhaust, UpCodes (text of the code as adopted in Minnesota)
  2. Minnesota Rules, part 1346.0050: Adoption of the International Mechanical Code, Minnesota Office of the Revisor of Statutes
  3. Clothes Dryer Fires in Residential Buildings (2008-2010), U.S. Fire Administration
  4. Overheated Clothes Dryers Can Cause Fires (Publication 5022), U.S. Consumer Product Safety Commission
  5. Rochester firefighters respond to fire caused by dryer vent, KTTC
MedCity Duct Cleaning

The MedCity Duct Cleaning Team

Locally owned and operated in Rochester, MN. We specialize in residential and commercial air duct and dryer vent cleaning using professional Rotobrush equipment.

Questions About Your Dryer Vent?

Request a quote, or call us with questions.

Call Free Quote